New windows and doors improve comfort, cut energy bills and add long-term value to your home. Sightline Windows & Doors Pinewood pairs proven product lines with our own installing crews for lasting performance - and a price we put in writing.
1. Choose your installer
The unit is half the job - the install is the other half. Our own background-checked crews measure, set, seal and insulate every opening, and they know the lines we quote inside and out because they install them every week.
2. Select the right products
Compare styles, materials and glass packages side by side until the fit is right for your rooms, your budget and your goals. The product-line comparison below is the place to start.
3. Prepare your home for install
Before install day we walk you through a short checklist - furniture pulled back, treatments down, a clear path to each opening - so install day is watch-it-happen, not scramble.
Compare the Lines We Quote
Every project is priced on the same lines, side by side - the price indicators below are relative, and your consultant shows exact numbers on your actual openings.
PGTThe line Florida homeowners arrive naming - the most Miami-Dade certifications in the industry$$$
- More Miami-Dade NOA certifications than any other line we quote
- WinGuard, EnergyVue and ClassicVue Max systems built for every wind zone
- 99% on-time delivery keeps your install date on the calendar
CGIThe heavyweight impact line$$$$$
- Large-missile impact ratings for the strictest wind zones
- Architectural-grade aluminum with commercial-depth frames
- The line we quote when protection is the whole point
CWSThe Florida value pick$$
- Vinyl systems built in Florida for Florida codes
- Strong energy packages at the friendliest price point
- The smart start for whole-home replacements on a budget
ESWSlim lines, big glass$$$$
- Narrow-sightline aluminum for modern elevations
- Oversized openings and floor-to-ceiling glass
- Impact-rated without the bunker look
ECOThe aluminum impact workhorse$$$
- Miami-built aluminum impact systems
- A strong price-to-protection ratio for coastal homes
- Proven inventory lines with short lead times
CGI Sliding & Patio Doors: The Pinewood Owner’s Guide
CGI sliding and patio door repair in Pinewood typically runs $340-$890 for track, roller, or lock hardware replacement, and $1,800-$4,200 for full panel replacement with impact-rated glass installed. We stock common CGI rollers, tandem assemblies, and mortise locks for same-day field repair on most series, and we measure every opening to the manufacturer’s spec sheet before ordering anything. Most Pinewood owners discover a problem when the door sticks in summer humidity, won’t latch after a tropical storm, or starts rattling against a frame that shifted in the heat.
Which CGI Models This Applies To
CGI builds sliding and patio doors across several series, and the parts are not interchangeable between them. The Estate Series uses a heavier tandem roller with a 1-1/4 inch stainless steel wheel and a specific sill track profile that differs from the Sentinel Series by roughly 3/16 inch in rail height. The Targa Series, common in Pinewood homes built 2018-2022 off Northwest 7th Avenue, runs a lighter-duty roller that wears faster under impact-rated panel weight but costs less to replace.
To identify your model, check the etched marking on the glass spacer or the label inside the frame header. The series code, glass thickness, and manufacturing date should all match the part we pull. We carry OEM CGI rollers and locks, plus a tested aftermarket line for discontinued series where OEM lead times stretch past three weeks. The aftermarket rollers we use match the 125-pound dynamic load rating and the 304-grade stainless housing; we won’t install a generic roller rated below the panel weight it carries.
One compatibility gotcha: the Estate Series 2008-2014 used a pre-revision mortise lock with a 7-5/8 inch faceplate that CGI later shortened to 7-1/2 inch. The holes don’t line up, and we’ve seen Pinewood homeowners order the current part only to find the mounting pattern wrong by that eighth inch.
Before
AfterSigns Your CGI Sliding & Patio Door Is Failing
- The door sticks or jumps the track. The tandem roller assembly has worn flat spots or lost bearing grease. In Pinewood’s summer humidity, aluminum oxide builds on the track and accelerates roller wear; we see this most on west-facing doors that bake from 2 PM onward.
- You need two hands to move the panel. Either the rollers have collapsed to metal-on-metal contact, or the track itself has dented from impact or foundation settling. A level check on the sill tells us which it is in about thirty seconds.
- The latch won’t catch or the lock cylinder spins. CGI mortise locks use a zinc housing that fatigues after roughly 8,000-12,000 cycles in coastal air. The internal cam cracks, or the cylinder setscrew backs out. Either way, the lock is no longer a security device.
- Visible gap at the header or sill when closed. The panel has dropped on worn rollers, or the frame has racked from thermal expansion. In Pinewood, we measure frame squareness with a laser; anything past 1/8 inch over the width means the door won’t seal against wind-driven rain.
- Condensation between the glass panes. The insulated glass unit (IGU) seal has failed. For impact-rated CGI panels, this means ordering a replacement IGU with the correct missile-impact certification label, not a standard dual-pane drop-in.
Replacement Cost & What’s Included
| Service | Typical Range in Pinewood | What’s Included |
|---|---|---|
| Roller / tandem assembly replacement | $340-$520 | OEM or matched aftermarket rollers, track cleaning, sill angle check, operation test |
| Mortise lock / handle set replacement | $280-$440 | Lock body, cylinder, strike plate alignment, key match to existing |
| Track repair or partial replacement | $420-$680 | Aluminum track insert or section replacement, drainage check |
| Full panel replacement (impact-rated) | $1,800-$4,200 | Measured survey, panel order, permit if required, install, photo record |
| IGU replacement (glass only) | $890-$1,640 | Custom-ordered sealed unit, argon fill, Low-E match, installation |
The range depends on three things: whether we have the part on the truck, whether the frame needs adjustment, and whether the original installation left us adequate clearance to work with. Every quote is written before we start; the number on the measured survey matches the invoice. The 365-Day Done Right Promise covers the installation and hardware function. Glass carries the manufacturer’s warranty, which varies by IGU construction.
DIY or Call Us?
What you can safely check: vacuum the track, look for visible roller debris, and test whether the door lifts slightly in its frame (if it does, the rollers have play). What goes wrong fast: removing a CGI impact-rated panel without proper support risks shattered glass, frame damage, or personal injury, the panel weighs 180-340 pounds depending on size and glass makeup. The tandem roller bolts are also set with thread-locking compound that shears off cheap Allen keys.
We’ve been called to Pinewood jobs where a homeowner bought the right roller but installed it with the adjustment screw upside-down, so the door rode on the housing instead of the wheel. Two weeks later the track was gouged and the repair cost tripled. Measure it right the first time and the second visit is a follow-up, not a fix.
For a written price on your specific CGI door, call (786) 574-6217. We’ll ask for the series name or a photo of the frame label, and we’ll tell you whether it’s a same-day fix or an ordered part.
FAQs
In coastal South Florida conditions, expect 7-12 years on OEM tandem rollers for standard use, or 4-7 years if the door faces west and gets heavy afternoon sun load on the frame. Salt air accelerates bearing corrosion even on stainless housings. Call (786) 574-6217 for an exact quote on replacement, estimates are free.
Sometimes. If the cylinder turns freely but the latch still throws, we can often rebuild the cam linkage. If the housing is cracked or the faceplate screw holes are stripped, replacement is the only sound repair. We carry both options on the truck and test before quoting. Call (786) 574-6217 for an exact quote, estimates are free.
Measured survey to final walkthrough is typically one day for a standard two-panel slider, assuming the rough opening is sound and no structural reframing is needed. Ordered panels from CGI currently run 4-6 weeks for impact-rated custom sizes. We don’t start demolition until the panel is in our warehouse. Call (786) 574-6217 to schedule the measured survey, estimates are free.
We stock rollers, locks, and weatherstrip for the Estate, Sentinel, and Targa series on every service vehicle. Estate Series pre-2014 mortise locks and discontinued series hardware are ordered with a 3-10 day lead time depending on CGI’s current production queue. Call (786) 574-6217 with your series name and we’ll confirm same-day availability, estimates are free.
Written by Sonia Raman, Owner, Sightline Windows & Doors Pinewood at Sightline Windows & Doors Pinewood, serving Pinewood and nearby areas.
Six Reasons Homeowners Choose Sightline Windows & Doors Pinewood
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.
Other Sightline Windows & Doors Pinewood Services
